question

Lorraine LIng avatar image
Lorraine LIng asked aliahmed answered

How to hard-reset clover mini 3rd gen?

Hi. Is there a way to hard reset the Clover Mini 3rd gen device? In previous models, there was a power button behind the receipt paper roll. Is there a different mechanism for mini-3rd?
Thanks. Lorraine

Clover Mini
1 comment
10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

rileytristan avatar image rileytristan commented ·
  1. Locate the power button on the Clover Mini device. It is usually located on the right-hand side of the device, near the top.
  2. Press and hold down the power button for about 10 seconds. Make sure to hold it until the device completely shuts down.
  3. Once the device is powered off, release the power button.
  4. Wait for a few seconds, then press and hold the power button again until the device powers back on.
  5. The device will go through the boot-up process and should reset to its default settings.
0 Likes 0 ·
jacobmilligan avatar image
jacobmilligan answered

Hello Lorraine,

The Mini 3's power button is a small, white button located on the back of the device. With the device facing you, it is directly behind the screen on the left hand side.

Hope this helps!

-Jacob

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Lorraine LIng avatar image
Lorraine LIng answered

Thanks Jacob, the white button is just what I was looking for!

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

donutamong avatar image
donutamong answered

Thank you. I found it. coreball

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

jacky avatar image
jacky answered

Thanks. I solved my problem. tiny fishing

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

larryellison avatar image
larryellison answered

I have solved the problem based on the instructions geometry dash bloodbath

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

williamliz125 avatar image
williamliz125 answered

Rileytristan gave a complete answer and It helped everyone to solve the difficulty.

five nights at freddy's 4

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

etherealestelle avatar image
etherealestelle answered

Sure thing! If you're looking to hard-reset your Clover Mini 3rd gen, it's pretty straightforward. Just hold down the power button for about 30 seconds until the device restarts. If you need a more detailed guide, Clover's support page has you covered.

By the way, if you're ever in need of some luxurious transportation, check out the Rolls Royce Ghost with Chauffeur. It's the epitome of elegance and comfort, perfect for making any occasion extra special!

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

pamelaladd avatar image
pamelaladd answered

I followed the guidelines to address the problem. geometry dash online

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

darlenewilkins avatar image
darlenewilkins answered

To hard-reset a Clover Mini 3rd Gen, press and hold the power button for about 40 seconds until the screen turns off and the device restarts. Alternatively, you can remove the power cable and reconnect it after a few seconds to perform a reset.

You might be more focused on your spacebar clicking speed using a timer. The Spacebar Clicker tool lets you track your click rate and turns it into a fun challenge. To get an accurate click rate, make sure to choose a timer of at least 5 seconds.



10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

tomdanny avatar image
tomdanny answered

Middlesbrough Grange Care Home offers a comfortable environment for residents and their families. If you need to hard-reset your Clover Mini 3rd Gen, start by unplugging the device from power. Wait for about 30 seconds before plugging it back in. Once powered on, press and hold the power button for 10 seconds until you see the reset prompt. Confirm the reset by following the on-screen instructions, ensuring your device returns to its factory settings.

10 |2000

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Write an Answer

Hint: Notify or tag a user in this post by typing @username.

Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Welcome to the
Clover Developer Community